Design of diamond-shape photonic crystal fiber polarization filter based on surface plasma resonance effect

A novel plasmonic polarization filter based on the diamond-shape photonic crystal fiber(PCF) is proposed. The resonant coupling characteristics of the PCF polarization filter are investigated by the full-vector finite-element method. By optimizing the geometric parameters of the PCF, when the fiber length is 5 mm, the polarization filter has a bandwidth of 990 nm and an extinction ratio(ER) of lower than -20 dB. Moreover, a single wavelength polarization filter can also be achieved, along with an ER of -279.78 dB at wavelength 1.55 μm. It is believed that the proposed PCF polarization filter will be very useful in laser and optical communication systems.     

A Photoluminescent Ag10Cu6 Cluster Stablized by a PNNP Ligand and Phenylacetylides Selectively and Reversibly Senses Ammonia in Air and Water

A photoluminescent bimetallic cluster [Ag₁₀Cu₆(bdppthi)₂(C≡CPh)₁₂(MeOH)₂(H₂O)](ClO₄)₄ ( 1 , bdppthi=N,N’-bis(diphenylphosphanylmethyl)-tetrahydroimidazole} was synthesized from the PNNP type ligand bdppthi generated in-situ. Upon excitation at 365 nm, 1 exhibited strong phosphorescent emission at 630 nm, which was selectively quenched by NH₃ in air or water. The sensing of NH₃ was rapid and recoverable, with detection limits of 53 ppm (v/v) in N₂ and 21 μmol/L (0.36 ppm, w/w) for NH₃ ⋅ H₂O in water. Cluster 1 could potentially serve as a bifunctional chemical sensor for the efficient detection of ammonia in waste-gas and waste-water.     

用标准件对梯度磁场定标

就标准厚度卡片在霍尔传感器的定标方面的应用作了有益的探讨。在纵向测量微小长度时,霍尔片处于磁场边缘位置,其对磁场的梯度更大,即灵敏度更高,且靠中心位置的线性更好。     

Sensitivity improvement of aluminum-based far-ultraviolet nearly guided-wave surface plasmon resonance sensor

An aluminum (Al) based nearly guided-wave surface plasmon resonance (NGWSPR) sensor is investigated in the far-ultraviolet (FUV) region. By simultaneously optimizing the thickness of Al and dielectric films, the sensitivity of the optimized Al-based FUV-NGWSPR sensor increases from 183°/RIU to 309°/RIU, and its figure of merit rises from 26.47 RIU^-1 to 32.59 RIU^-1 when the refractive index of dielectric increases from 2 to 5. Compared with a traditional FUV-SPR sensor without dielectric, the optimized FUV-NGWSPR sensor can realize simultaneous improvement of sensitivity and figure of merit. In addition, the FUV-NGWSPR sensor with realistic materials (diamond, Ta₂O₅, and GaN) is also investigated, and 137.84%, 52.70%, and 41.89% sensitivity improvements are achieved respectively. This work proposes a method for performance improvement of FUV-SPR sensors by exciting nearly guided-wave, and could be helpful for the high-performance SPR sensor in the short-wavelength region.     

The single-polarization filter composed of gold-coated photonic crystal fiber

A single-polarization filter comprising a gold-coated photonic crystal fiber based on surface plasmon resonance is designed and investigated. The pattern matching and coupled polarization characteristics analyzed by the full-vector finite element method (FEM) and losses at 1,540 nm are achieved to 1,016.01739 dB/cm (x-pol core mode) and 33.81917 dB/cm (y-pol core mode). The crosstalk (CT) value of the 1,540 nm band is ?853.12653 dB for fiber length $L=1,000\mathrm{\mu }\text{m}$ and the bandwidth is 850 nm. The working wavelength of the filter ranges from 1,280 nm to 1,540 nm by varying the diameter of outer air holes ($d_1$), the diameter of inner air holes ($d_4$), the metal film thickness (t), as well as the liquid refractive index (n).     

光寻址电位传感器的正交相位检波检测方法

光寻址电位传感器的幅度检测方法易受噪声干扰,灵敏度差,信噪比和精度低,且受调制光源的影响较大,影响检测结果的准确性.为此提出了一种基于正交相位检波的光寻址电位传感器检测方法.该方法是将光寻址电位传感器的输出光电流信号分别与两路正交信号相乘,通过低通滤波提取直流分量并相除,即可得到光寻址电位传感器的输出信号相位信息.与已有的光寻址电位传感器相位检测方法相比,该方法具有算法复杂度低、实时性高的优点.实验研究了调制光源光强对光寻址电位传感器幅度检测和相位检测的影响,对比分析了光寻址电位传感器的传统幅度检测方法与正交相位检波检测方法对pH检测的灵敏度、线性度及信噪比.结果表明,相比于幅度检测方法,调制光源光强对光寻址电位传感器的相位检测影响更小,在频率为10 kHz,pH的范围为1.68~10.01的情况下,相位检测方法比幅度检测方法测得的灵敏度增加了7 mV/pH,精度提高了14.9 mpH,非线性误差减小了0.003%,均方差减少了0.1051×10^-5,信噪比增加了8.2827 dB.该方法特别适用于弱光下的光寻址电位传感器检测.     

Voltammetric Determination of Isoniazid Drug in Various Matrix by Using CuOx Decorated MW‐CNT Modified Glassy Carbon Electrode

Copper oxide decorated multi‐walled carbon nanotube (MWCNT) modified glassy carbon electrode (GCE) was prepared for determination of isoniazid (INZ) in various matrices. The electrochemical behavior of INZ was tested with the aid of Cyclic Voltammetry (CV) and quantitative experiments were performed by using Linear Sweep Voltammetry (LSV). Morphological and structural characterization of the modified electrode was performed by utilizing Scanning Electron Microscopy (SEM), X‐Ray Photoelectron Spectroscopy (XPS) while electrochemical characterization was performed by using CV and Electrochemical Impedance spectroscopy (EIS). The proposed sensor exhibited well defined anodic peak at 0.30 V for INZ at pH 6.0 medium. Under the optimum conditions, a linear relation between INZ concentration and peak current was observed in the range of 2.0×10^?7 to 5.0×10^?5 M. Limit of detection was calculated as 1.0×10^?8 M and repeatability and accuracy was found as 5.60 % and 91.0 % for 5.0 10^?7 M INZ by using 3 successive measurement, respectively. Then, the analytic performance of the electrode developed was tested by analyzing commercial tablets, artificial human serum and urine samples. The results indicated that satisfactory recoveries was observed for all issue.     

A model for crack formation during active solid pyrolysis of a char-forming solid: crack patterns; surface area generation; volatile mass efflux

A model is developed for the formation and propagation of cracks in a material sample that is heated at its top surface, pyrolyses, and then thermally degrades to form char. In this work the sample is heated uniformly over its entire top surface by a hypothetical flame (a heat source). The pyrolysis mechanism is described by a one-step overall reaction that is dependent nonlinearly on the temperature (Arrhenius form). Stresses develop in response to the thermal degradation of the material by means of a shrinkage strain caused by local mass loss during pyrolysis. When the principal stress exceeds a prescribed threshold value, the material forms a local crack. Cracks are found to generally originate at the surface in response to heating, but occasionally they form in the bulk, away from ever-changing material boundaries. The resulting cracks evolve and form patterns whose characteristics are described. Quantities examined in detail are: the crack spacing in the pyrolysis zone; the crack length evolution; the formation and nature of crack loops which are defined as individual cracks that have joined to form loops that are disconnected from the remaining material; the formation of enhanced pyrolysis area; and the impact of all of the former quantities on mass flux. It is determined that the mass flux from the sample can be greatly enhanced over its nominal (non-cracking) counterpart. The mass efflux profile qualitatively resembles those observed in Cone Calorimeter tests.     

强度解调型光纤光栅温度传感实验

光纤光栅在工程上应用广泛,但由于存在解调系统复杂、成本高,尤其是需要使用光纤光谱仪等波长解调仪器,使得光纤光栅很难走入本科教学的实验课堂.本文提出了一种基于窄线宽DFB激光器的强度解调方案,极大地简化了光纤光栅传感器的解调系统,完全满足较高分辨率和实时检测的系统要求.合理安排的温度传感实验可以非常直观地展示光纤光栅的线性传感性能,使得工程化的光纤光栅传感技术轻松走进本科教学课堂,具有极高的推广和应用潜力.